Losi Promoto Motorcycle Light Kit

Amp up your Promoto Motorcycle with MyTrickRC's Losi Promoto Motorcycle Light Kit!  The Losi Promoto Motorcycle Light Kit is a sleek and simple Light kit that's a snap to install and has Nice Bright Light Pods in front and a Sleek Tail Light Pod tucked up inside the rear fender.   The mounting locations of the LEDs on the Losi Promoto Motorcycle Light Kit were chosen to protect them from impacts.  The locations are away from the bikes normal high impact, wear areas.  Additionally, the LEDs on the Losi Promoto Motorcycle Light Kit meet MyTrickRCs standard for crazy brightness, even in broad daylight.   

NOTES:

This Kit powers directly off the receiver.

The Tail Light includes an strong Adhesive Pad for installation, however, if you want added security in the adhesion to the rear fender,  also adding some Zap Goo, Shoe Goo, or E-6000 around a couple edges works very well for these parts.  These adhesive bond to both parts well.

**Be sure the rear fender is very clean before applying the Tail Light Pod.  Clean the Promoto's  rear fender with isopropyl (rubbing alcohol).  Clean surface twice, allow the alcohol dry fully, then install Tail Light Pod by pressing the adhesive pad on the Tail Light Pod firmly in place.  It takes about 24hrs for the adhesive pad to fully bond to both parts.   Use the bike gently during the 24hrs after installing the tail light pod.                                                 

Features:

• Simple, hassle-free operation
• EasyAssembly and Installation
• Custom made kit compliments the Promoto's rad styling
• LEDs are very Bright and Functional Day and Night
• Powers On/Off with the Bike

Kit Includes:

• 1-PAL3 Power Supply
• 1-Pair SQ4 Light Pods
• 1-Tail Light Pod

Installation:

Remove Left Side Panel.

Connect the Light Pod to the Power Supply and place as shown.  Connect the Light Pods to either black connector on the Power Supply.  You can use double back tape, Zap Goo, Zap Goo, or E-6000 to bond the Power Supply to the bike.

Next feed Tail Light wire though the small hole in the metal plate on the side of the bike, as shown.  Connect the Tail Light to the white port on the Power Supply.

 Light Kit is now installed.  Re-Install Motor Cover and Left Side Panel, you are DONE!

• PAL3 Power Supply
• Simple Install
• Super Bright
• Tail Light Pod
• Expandable

MyTrickRC's Losi Grave Digger Monster Truck Light Kit is the perfect light kit upgrade to bring your Grave Digger to life!   

This incredible kit uses MyTrickRC's new HB-2 LED Light Controller to power Grave Diggers iconic redeye headlights and a striking green underglow! 

Losi Grave Digger Monster Truck Light Kit Includes:

• 1 - HB-2 LED Light Controller
• 1 - 17mm RED Halo Headlights
• 3 - SQ4 10mm Square GREEN Wafer LEDs
  
• 1 - SP1 RED Tail Light Pods 
• 1 - 2-Way LED Splitter 
• 1- 3D Printed Headlight Buckets
• 1- 3D Printed Controller Mount Bracket
• Zip Ties and Zip Tie Mounts for clean wiring management
  
• MyTrickRC Bumper Stickers

.

• HB-2 Controller
• Terrifying Red Halos
  
• Wicked Tail Light Pods
  
• Scary Bright Under Glow
  
• Expandable 

The Element RC Bushido Light Kit 

Looking for the ultimate lighting setup for your Element RC Bushido? Look no further, the MyTrickRC Element RC Bushido Light Kit is perfect! 

The Element RC Bushido Light Kit features the CX-1 Controller at its heart. A Compact LED Light Controller that powers off of a free port in your receiver or one the 5.0V ports Element RC provides on their Reedy ESC. The Element RC Bushido Light Kit also includes 3D Printed Tail Light Buckets that fit the stock body. The Element RC Bushido Light Kit is Plug and Play and easy to install.

Features:

• Easy Installation 
• Waterproof LEDs
• 3-D Printed Tail Light Buckets

Kit Includes:

• CX-1 Controller
• 1 Dual Halogen 5mm LEDs
• 1 Dual Red 3mm LEDs
• 2 Pair Attack Spot Light LEDs
  
• 3D Printed Tail Light Buckets
• Zip Ties and Zip Tie Mounts for clean wiring management
• MyTrickRC Decal
  

• CX-1 Controller
• Rock Lights
• Period correct Halogen Headlights
• Tail Lights

MyTrickRC's Traxxas Ultimate RC Hauler Kit is the perfect light kit upgrade for your Ultimate RC Hauler Tow Truck.   

This incredible kit uses MyTrickRC's new UF-7R Controller.  One of the coolest aspects of the Traxxas Ultimate RC Hauler Kit is the UF-7R's flexibility, allowing you to configure your light system different ways depending on how you want it!   

By slightly changing the way LEDs are connected, and selecting a different MODE, you can easily configure, or change up your settings.  Everything you need for all configurations is included in the kit.  

SETUP #1 - Functioning Turn Signals

If you want a scale setup with functioning Turn Signals the Traxxas Ultimate RC Hauler Kit can do that. Set the UF-7R to MODE 7 and connect LEDs as shown:

• Port A - Reverse
• Port B - Left Rear Tail/Brake/Turn (use 2-way cables)
• Port C - Right Rear Tail/Brake/Turn
• Port D - Front Right Turn
• Port E - Headlights
• Port F - Front Left Turn

*This configuration doesn't support On/Off Control of Flasher Bar. MyTrickRC has solution for this coming soon.

SETUP #2 - Staged Lighting Control

Or, if you prefer a setup for Rock Crawling that has Scale Brakes and Reverse, and the ability to power a Flasher Bar then you want setup #2. By connecting UF-7R's Input 2 to the transmission servo, you can use the transmission switch to toggle through staged lighting. Staged lighting starts with all Lights OFF. the first toggle turns on front running lights, Tail/Brake, and Reverse. The next level adds Headlights, and the last level turns our port G which you can use to power a Flasher Bar, and/or High Power LEDs like Rock Lights, or Utility Lights.  Set the UF-7R to MODE 3 and connect LEDs as shown: 

• Port A - Reverse
• Port B - Blinking (not used)
• Port C - Tail/Brake
• Port D - Front Running Lights
• Port E - Headlights
• Port F - Center Bake (not used)
• Port G - High Power Output (not used)

SETUP #3 - Remotely Controlled Strobes

For Emergency Use Setup with wig-way strobes, set the UF-7R to MODE 10 and connect LEDs as shown: 

• Port A - Wig-Wag Strobe (side A)
• Port B - Tail/Brake (use 2-way cables)
• Port C - Slow Strobe (not used)
• Port D - Wig-Wag Strobe (side B)
• Port E - Headlights
• Port F - Slow Strobe (not used)
• Port G - Flasher Bar (optional)

*This configuration does support On/Off Control of a Flasher Bar, along with the strobes.  Connect UF-7R's input 2 to the transmission channel on your receiver.  You will have Tail/Brake function and Strobes in the Front Running Lights and Reverse.  Tail/Brake will function normally.

**The Traxxas Ultimate RC Hauler Light Kit does not come with a Flasher Bar, that is sold separately.  You can purchase that link here.  Click picture to view Flasher Bar.

Traxxas Ultimate RC Hauler Light Kit Includes:

• 1 - UF-7R Light Controller
• 2 - 5mm Single White LEDs (700mm)
• 2 - 5mm Single Red LEDs (700mm)
• 1 - 5mm Dual White LEDs
• 2 - 3mm Single Orange LEDs
• 2 - 5mm Single Red LEDs
• 2 - 2-Way LED Splitters
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

• UF-7R Controller
• Full Running Lights
• Scale Reverse Function
• Multiple Modes
• Expandable

Element RC Ecto Light Kit 

The perfect complement to your Element RC Ecto, is the ability to go anywhere at anytime; day or night!

The Element RC Ecto Light Kit is a Hight Power Light Kit based on the HB-2 LED Light Controller. The Element RC Ecto Light Kit pumps out TONs of Light, so all of your friends who don't have this kit will be envious of the Scale Look and amazing performance! 

The Element RC Ecto Light Kit is plug & play, making installation simple and hassle free!

The Ecto Light kit also come with cleans lenses and a couple FREE Ecto 3D Grill/Light Bucket files to print and add the extra POP, to your build.

Features:

• Simple, hassle-free operation
  
• Easy Installation 
• In-Line Quick Disconnects between Body and Chassis

Kit Includes:

• 1-HB-2 LED Light Controller
• 1-Dual Red 5mm
• 1-27mm Strip LED
• 1-Clean lenses
• 3D Print files (Online)

3D Grill Installation

Start be cutting away the grill section of your Element RC Ecto body.

Note: Cut right on the edge of where the body dips down into the grill area. Be careful not to cutaway too much!

Next you will take your 3D printed grill and insert the 27mm strip LEDs from the rear. 

NOTE: Take your time and insert the LED's with care. 

Once installed from the rear of the grill, you can cover the LED strips with the included clean lenses. 

NOTE: Insert lenses with care being sure to note any flash or fitment issues with the 3D print. The lenses should fit snug, NOT TIGHT. 

You can now slide your assembled grill/light setup into the Ecto body. We recommend a silicone-based adhesive such as ZapGoo, e6000, ShoeGoo or equivalent. 

Rear LED Installation: 

To install the tail lights on your Ecto, you will need to first make some holes in the body where you would like to locate your LEDs. 

Note: Be sure not to make your holes too big, the LED holder will not work correctly. 

After you make your holes, insert the included LED holders into the body from the outside.

Once the holders are installed, you install the LED's from the inside of the body. 

Once installed, we again recommend a small amount of silicone-based adhesive on the back of the LED's to help hold them securely in place. 

3D Print Your Own Grill!

• The Element RC Ecto Light Kit  was designed to work with some of the downloadable 3d grill files below.  
• Be sure to print your grill in a material that can handle the heat the LEDs will generate. We recommend ABS or Carbon Nylon.   PLA/PLA+ prints will likely not handle the heat and will deform. 

Click the grill image to download the files

NOTE - Dimension of 3D Prints varies with different printers.  If clear lenses are too tight to fit properly, try scaling up or modifying the STL file.

• HB-2 Controller
• Grill Included
• Super Bright
• Tail Lights
• Expandable

 RC4WD XtraCab Light Kit

The RC4WD XtraCab Light Kit is a Clean and Simple Way to get an Awesome Scale Look on your RC4WD XtraCab. 

You'll be impressed how much the RC4WD XtraCab Light Kit will scale up your build. Folks who have seen it love the look of the Halogen Headlights, not to mention the Scale Running Lights, Working Brake and Reverse Lights, and parts needed to install optional Turn Signals. This kit also includes Automatic Hazard Lights so you can get the Most Scale Results!  Hazard Light function can be easily be toggled On or Off.  Oh, did we mention that if you opt out of Turn Signals, the extra Servo Cable can be use for Remote ON/OFF 3rd Channel Control of the all the Lights?

Yes, that's how Insanely Awesome the RC4WD XtraCab Light Kit is!  The RC4WD XtraCab Light Kit offers you more Scale Options!  Also, with the UF-7C Controller, you can also easily add more lights if you want. This could include Rock Lights, Light Pods, Side Markers, Blinking Dust Light, Lights for the Stock Light Canisters.

Features:

• Scale Halogen Headlights, Rear Tail/Brake Lights, Front Running Lights and Reverse
• Automatic Hazard Lights
• Remote ON/OFF Control of all LEDs on 3rd Channel
• Expandable System = Easily add MyTrickRC Spot Lights (as Rock Lights) or Light Bar
• Rock Solid UF-7C Lighting Controller is a is an Industry Leader for Quality Scale Lighting solutions
• Ultra Bright 5mm & 3mm LEDs.
  

Light Kit Includes:

• 1pc UF-7C Lighting Controller
• 1pc 5mm Dual HALOGEN Headlights
• 1pc 3mm Dual ORANGE Running Lights
• 4pc 3mm Single ORANGE Turn signals
• 1pc 3mm Dual RED Tail/Brake Lights
• 1pc 3mm Dual WHITE Lights
• 2pc Servo Y Cable For Brake/Rev and Turn Signals
• Zip Ties and Zip Tie Mounts for wiring management
• Attack Scale Bumper Stickers

• UF-7C Controller
• Ultra Scale Light Kit
• Optional Turn Signals
• Reverse Lights
• Plug and Play

Axial Deadbolt Light Kit

The perfect complement to a 'go anywhere' vehicle, is the ability to go at anytime; day or night! 

The Axial Deadbolt Lighting Kit is the perfect upgrade to push your build to the next level. 

Features:

• Sleek looking LED Headlights and Curved Light Bars
• Attack High Powered Headlights
  
• Expandable System = Adding More Lights is Plug-and-Play
• Ultra Bright LEDs, MyTrickRC does not compromise on component quality
• Impact Resistant Light Bar Design can take a beating
• HB-2 LED Light Controller is easy to wire up, can be powered directly off your Battery.

Includes:

• 1- HB-2 Controller
• 1- 5" Attack Light Bar
• 2- Pair High Power Spot Lights
• 1- 3mm Dual Red Tail/Brake Lights
• 1- 3mm Dual  Amber Running Lights
• 1- 4-Way LED Splitter
• Zip Ties and Zip Tie Mounts for clean wiring management
• MyTrickRC Stickers

• HB-2 Controller
• 5" Attack Light bar
• 2" Light Bar
• 1pc Rock Lights
• Plug and Play

Axial RR10 Bomber Light Kit 

The perfect complement your Bomber, is the ability to go at anytime; day or night!

The Axial RR10 Bomber Light Kit is nice and compact, and offers some great features including High Power Headlights and Rock Lights and rear lighting with functioning Tail/Brake lights. Also, the Axial RR10 Bomber Light Kit is Plug and Play! The Axial RR10 Bomber Light Kit is Super Bright, and really takes your Bomber to the Next Level.

Features:

• Hi Performance
• Easy Installation
• Plug and Play
• Waterproof
• On/Off Switch

Axial RR10 Bomber Light Kit Includes:

• HB-2 Controller
• 2 Pair High Power Spot Lights
• 1pc 3-Way LED Splitter
• 5 Inch Attack Light Bar
• 2 Inch Attack Light Bar
• 3D Printed Light Bar Mounts
• 1-5mm Dual Red
• 1-5mm Dual Amber
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

• Ultra Compact Design
• High Intensity LEDs
• Keep Stock Light Bar
• Includes Rock Lights
• Plug and Play

Axial Early Bronco Light Kit

Axial Early Bronco Light Kit!  This kit includes the NEW Attack Halogen High Power adjustable brightness Headlights, Front Marker Lights and Tail Lights. The kit is fully expandable, with the ability to add Rock Lights and more light bars.  

The Axial Early Bronco Light Kit has some great features including Adjustable Brightness on multiple ports Headlights, Light Bars and LEDs. This is great for power management, simply Plug and Play Installation, and it was built specifically to fit your truck.

Minor modifications to the body (Windshield) are required for installation. 

NOTE:

Installation Video shows a DG-1 Dragon Controller, however this kit now comes with an HB-2 Controller instead.  Simply plug Headlights into HB-2 Port D, Light Bars & Rock Lights into ports E and F.  3mm and 5mm LEDs plug into ports A, B, or C.  The HB-2 doesn't have any remote functions.   

Includes:

• HB-2 LED Light Controller
• 1pc Attack  6" Light Bar
• 1pc Attack  2" Light Bar
• 1pc Attack  Halogen High Power Headlights
• 1pc 5mm Dual Red Tail Lights
• 1pc 5mm Dual Amber Front Marker Lights
• 1pc 3D printed LED mounts

• Halogen Headlights
• 6" and 2" Light Bars
• Tail/Brake Lights
• Expandable
• MyTrickRC Stickers

Axial Ryft Attack Light Kit

The Axial Ryft Attack Light Kit is the perfect compliment to your Axial Ryft RBX10.

The MyTrickRC Axial Ryft RBX10 Attack Kit is nice and compact, and offers all High Power LED Headlights with Mounting Bracket, Taillight Bar and Rock Lights.

Our UF-7R Lighting Controller comes on this kit, and it draws power directly from the receiver. The Axial Ryft RBX10 Attack Light Kit is Plug and Play and the Lights will be ON whenever the truck is On.

Features:

• Hi Performance / Integrated Light Buckets
• Insanely Bright Light Kit for your Ryft
• Easy Installation
• Minimal Wiring

Includes:

• UF-7R Controller
  
• 1 Pair of White Attack 27mm Strip Headlights
• 1 Pair of Red Attack 27mm Strip Tail Lights
• 2 Pair High Spot Lights
• 1pc 3-Way LED Splitter
• Zip Ties Set
• Attack Scale Bumper Stickers
• Custom Headlight and Tail Light Mounts
  
• 1 Y-Cable for ESC

NEW Improved Design Instructions:

STEP 1 - Remove Excess Support Material from Parts

STEP 2 - Insert LED into Rear Light Bar with LEDs facing outward as shown.  NEVER pull on LEDs, always push LED through hole.  The flexible part of the LED is somewhat fragile and can break if you twist them too much during installation.

STEP 3 - Gently bend the LED onto it's own wire as shown

STEP 4 - Apply Zap Goo, Shoe Goo, or E6000 to LED pockets of Light Bar

STEP 5 - Push wire into glue, then apply a second layer for the LED to bond to

STEP 6 - Apply a SMALL amount of glue to the top of the PCB.  BE CAREFUL not to get glue on the LEDs.  If you do, then wipe it off before installing the lenses.  Only a SMALL amount of glue is needed here

STEP 7 - Press in the Lenses.  Tail Lights are DONE!

STEP 8 - Apply Zap Goo, Shoe Goo, or E6000 to LED to the Headlight Bracket as shown

STEP 8 - Place the LED as shown, with the flexible end hanging off the part.  We recomend that you apply a small amount of tape to hold the LED in position before doing the other side.

STEP 9 - Once LED glue is fully set, wrap the wire around the Bracket.  Be sure to hook the wires into the small C clip on the Bracket.  Apply a more generous amount of glue here to both the C Clip area, and the flexible part of the LED to provide it good support after drying.  You are DONE installing the LEDs!

• Ultra Compact Design
• High Intensity LEDs
• Includes SpotLights
• Plug and Play
• Tail Light Bar

Axial SCX10 III Rubicon Light Kit 

The perfect complement to your Rubicon, is the ability to go at anytime; day or night!

The MyTrickRC Deluxe Axial SCX10 III Rubicon Light Kit Completes your Axial Rubicon build!

Axial did an amazing  job on the SCX10 III Rubicon by adding Tons of Scale Features, so we also pulled out all the stops on this kit, with a long list of killer features like Dual Light Headlights that have Crazy Bright White Halos on the outside plus Separate Center LED.

The Axial SCX10 III Rubicon Light Kit also comes with Rock Lights which include an inline quick disconnect, so that you can easily separate the body from the chassis. Plus Tail/Brake Lights, and Interior Lights!   For sure, our Axial SCX10 III Rubicon Light Kit takes it to the next level! 

But in addition to all this, numerous 3D printed parts for Headlights, Tail Lights, Rock Lights, and Interior Lights come included.  This makes the Axial SCX10 III Rubicon Light Kit Easier than Ever to install and get Awesome Results!  True to the MyTrickRC philosophy, the Axial SCX10 III Rubicon Light Kit kit is a direct fit to the Rubicon, and doesn't require any cutting or gluing. Now that's how to Trick Out your RC!  Outfit your Axial Rubicon build with the MyTrickRC Deluxe Axial SCX10 III Rubicon Light Kit, and have more Safety, and Fun on the trail! 

Features:

• Crazy Bright Dual Headlight Setup
• Interior Lighting and Rock Lights
• Brake Lights 
• Quick Disconnect to separate Body from Chassis
• Easy Installation  Plug and Play
• On/Off Switch

Kit Includes:

• HB-2 Lighting Controller
• 1 Pair High Power White Halo Headlights
• 1 Pair 5mm Dual White (Center Headlight LED)
• 1 Pair 5mm Dual Red (Tail/Brake)
• 1 Pair High Power Headlights (Interior)
• 2 Pair High Power Rock Lights
• 1 pc Port Conversion Cable (for Center Headlights)
• 1 pc 4-Way LED Splitter (for Rock Lights)
• 1 Set 3D Printed Parts (for Headlights, Interior, Rock Lights)
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

NOTE 

        This kit is recommended for use on the Axial Gladiator, however our 3D printed Tail Light inserts aren't meant to be used on the Gladiator. Also, the Dashboard Lights require you to cut the Dashboard, fabricate a clear lens, and transfer of stickers. This is only recommended for advanced modelers.

• Dual Headlights
• Interior Lights
• Rock Lights
• Plug and Play
• HB-2 Controller

Axial Jeep XJ Attack Light Kit

The perfect complement to your Axial Jeep XJ is the ability to go at Anytime - Day or Night!

The Axial Jeep XJ Attack Light Kit is a Clean and Simple Way to get an Awesome Scale Look on your Axial XJ.  You'll be impressed how much the Axial XJ Attack Light Kit adds to the Jeep XJ stock body.  Folks who have seen it love the look of the super bright Attack Headlights, not to mention the Scale Running Lights. Yes, that's how Insanely Awesome the Axial Jeep XJ Light Kit is!

Also, with the HB-2 Controller, you can also easily add more lights if you want. This might include Side Markers, Additional Canisters that came with the Truck, Dust Light, Halogen Lights for the Stock Light Canisters, or even a couple sets of Spot Lights to use as Rock Lights (Rock Lights power directly off the Receiver). The kit comes standard with our HB-2 Light Controller; a sleek, easy to setup, and simple to use light controller featuring 6 individual output ports 3 standard power, 1 mid power, and 2 High power. This port configuration gives you the ability to create various combinations of 3 and 5mm LEDs, Rock Lights, etc. in various colors!

Features:

• Super Bright Attack 19mm Rectangular Headlight
• 3D Printed Tail Light Buckets
• ON/OFF Switch
• Expandable System = Easily add MyTrickRC Spot Lights (as Rock Lights) or Light Bar
• HB-2 Lighting Controller
• High Quality Components

Kit Includes:

• 1pc HB-2 Lighting Controller
• 1pc 5" Attack Light Bar
• 1pc Dual Attack 19mm Rectangular Headlights
• 1pc Quad 3mm ORANGE, RED Running Lights
• 1pc 3mm Dual WHITE Reverse Lights
• 1pc 3D Printed Tail Light Buckets
• MyTrickRC Scale Bumper Stickers
• Zip Ties and Zip Tie Mounts for clean wiring management

NOTE - Light Bucket Installation requires scraping off paint under the tail light stickers. Be careful to make sure that you scrape per the sticker location. Lines molded on the body may not match the tail light stickers location so start by scraping a small dot, then verify its position by shining light through the area scraped.

• Scale Light System
• HB-2 Controller
• Attack 19mm Rectangular Headlights
• Easily Add More Lights
• Tail, Brake

The Axial Capra Light Kit is the perfect compliment to your Axial Capra!

The MyTrickRC Axial Capra Light Kit is nice and compact, and offers some great features including High Power Headlights and Rock Lights. No Lighting controller needed on this one, its all powered off our Standard Light Bar Power Regulator, drawing power directly from the receiver!

It's Plug and Play and the Lights will be ON whenever the truck is On. With the Axial Capra Light Kit you can keep the stock Light Bar untouched, retaining the sleek look of the stock truck.

Features:

• Hi Performance / Low Cost
• Easy Installation
• Minimal Wiring
• Plug and Play

Includes:

• MyTrickRC Light Bar Regulator
• 1 Pair High Power Headlights
• 2 Pair High Power Rock Lights
• 1pc 3-Way LED Splitter
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

The Standard Light Bar Regulator is NOT for use with 3mm and 5mm LEDs, it will burn them up immediately! Do not connect more lights than your Receiver and ESC are rated for. Input 4.5-9VDC DO NOT Exceed 9V on the input. Output: 4.9VDC +/- .1V 1.2Amp MAX

• Ultra Compact Design
• High Intensity LEDs
• Keep Stock Light Bar
• Includes Rock Lights
• Plug and Play

Axial Blazer Vintage Light Kit

The Axial Blazer Vintage Light Kit is a Clean and Simple Way to get an Awesome Scale Look on your Axial Blazer! 

You'll be impressed how much the Axial Blazer Vintage Light Kit adds to the 69 Blazer stock body.  Folks who have seen it love the look of the Halogen Headlights, not to mention the Scale Running Lights, Working Brake and Reverse Lights.

This kit also includes Tail Light Buckets, and Automatic Hazard Lights so you can get the best results! Oh, did we mention Remote ON/OFF 3rd Channel Control of the Lights? Yes, that's how Insanely Awesome the Axial Blazer Vintage Light Kit is!

Also, with the UF-7C Controller, you can also easily add more lights if you want. This might include Side Markers, Additional Canisters that came with the Truck, Blinking Dust Light, Halogen Lights for the Stock Light Canisters, or even a couple sets of Spot Lights to use as Rock Lights (Rock Lights power directly off the Receiver).

Features:

• Scale Halogen Headlights, Rear Tail/Brake Lights, Front Running Lights and Reverse
• 3D printed Taillight Buckets
• Automatic Hazard Lights
• Remote ON/OFF Control of all LEDs on 3rd Channel
• Expandable System = Easily add MyTrickRC Spotlights (as Rock Lights) or Light Bar
• Rock Solid UF-7C Lighting Controller is a is an Industry Leader for Quality Scale Lighting solutions
• High Quality Components 

Includes:

• 1pc UF-7C Lighting Controller
• 1pc 5mm Dual HALOGEN Headlights
• 1pc 3mm Dual ORANGE Running Lights
• 1pc 3mm Dual RED Tail/Brake Lights
• 1pc 3mm Dual WHITE Lights
• 1pc Extra Power Cable for Remote On/Off Control
• 1pc 3D Printed Taillight Buckets
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

NOTE - Light Bucket Installation requires scraping off paint under the taillight stickers. Be careful to make sure the you scrape per the sticker location. Lines molded on the body may not match the taillight stickers location so start by scraping a small dot, then verify its position by shining light through the area scraped.

• Scale Light System
• UF-7C Controller System
• Halogen Headlights
• Easily Add More Lights
• Tail/Brake + Reverse

Axial SCX24 C10 light Kit

MyTrickRC's Axial SCX24 C10 Light Kit is the brightest on the market!  

You get the same Attack headlights used in our 1/10 scale kits!  Some great features of the Axial SCX24 C10 Light Kit are Attack High Intensity Halogen Headlights that offer a ultra-scale look, and they are bright enough to shine right through the Headlight Stickers that come on the C10. 

Additionally, the Axial SCX24 C10 Light Kit comes with our all new CX1- light controller powers 3 High-Power and 4 low Voltage for standard LEDs. The Axial SCX24 C10 Light Kit also includes Orange Front Bumper lights as well as Red Taillights. Keeping things just as accurate on a smaller scale.  

Features:

• Scale High Powered Headlights
• CX1 Lighting Controller
• Easy Plug and Play into stock RX
• High Quality Components 
• Higher Gauge wires over stock for long life
• Expandability

Includes:

• 1pc CX-1 Light Controller
• 1 pair Attack Halogen Headlight
• 1pc Dual 3mm Red Taillights
• 1pc Dual 3mm Orange Front Running Lights
• 3D Printed Headlights Mounts
• 3D Printed Taillight Buckets
• Attack Scale Bumper Stickers
• Zip Ties and Zip Tie Mounts for clean wiring management

• CX-1 Controller
• Halogen Headlights
• Tail Lights
• Plug & Play
• 3D Buckets

Axial Scx24 Deadbolt light Kit

Axial SCX24 Deadbolt Light Kit the brightest on the market.

You get the same Attack headlights used in our 1/10 scale kits. All new CX1- light controller powers 7 accessory lighting ports, 3 High-Power and 4 low Voltage for standard LEDs. the kit also includes Amber Front driving lights as well as Red Taillights. Keeping things just as accurate on a smaller scale.  

Features:

- Scale High Powered Headlights

- CX1 Lighting Controller

- Easy Plug and Play in to stock RX

- High Quality Components 

- Higher Gauge wires over stock for long life

Includes:

• 1pc CX-1 Light Controller
• 1 pair Attack Headlight
• 2 Single Red 3mm LED 
• 2 Single Amber 3mm LED
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers
• 3d Printed Grill
• 3d Printed Rear Tail Light Buckets
• CX-1 Controller
• High Intensity LEDs
• Sleek Look
• Plug and Play

• CX-1 Controller
• Scale Headlights
• Tail Lights
• Plug and Play
• 3D Buckets

Axial SCX24 Jeep JLU light Kit

MyTrickRC's Axial SCX24 Jeep JLU Light Kit is the brightest on the market! You get the same Attack headlights used in our 1/10 scale kits!

Some great features of the Axial SCX24 Jeep JLU Light Kit are Attack Headlights that offer a ultra-scale look.

Additionally, the Axial SCX24 Jeep JLU Light Kit comes with our all new CX1- light controller powers 3 High-Power and 4 low Voltage for standard LEDs. The Axial SCX24 Jeep JLU Light Kit also includes Orange Front Bumper lights as well as Red Taillights. Keeping things just as accurate on a smaller scale.  

 Features:

• Scale High Powered Headlights
• CX1 Lighting Controller
• Easy Plug and Play into stock RX
• High Quality Components 
• Higher Gauge wires over stock for long life
• Expandability

Includes:

• 1pc CX-1 Light Controller
• 1 pair Attack White Headlight
• 1pc Dual Red 3mm LED Taillights
• 1pc Dual Amber 3mm LED Front Running Lights
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers
• 3D Printed Rear Taillight Buckets

• CX-1 Controller
• Attack Headlights
• Tail Lights
• Plug & Play
• 3D Buckets

Axial SCX24 Jeep Gladiator

MyTrickRC's Axial SCX24 Jeep Gladiator Light Kit is the brightest on the market! You get the same Attack headlights used in our 1/10 scale kits!

Some great features of the Axial SCX24 Jeep Gladiator Light Kit are Attack Headlights that offer a ultra-scale look.

Additionally, the Axial SCX24 Jeep Gladiator Light Kit comes with our all new CX1- light controller powers 3 High-Power and 4 low Voltage for standard LEDs. The Axial SCX24 Jeep Gladiator Light Kit also includes Orange Front Bumper lights as well as Red Taillights. Keeping things just as accurate on a smaller scale.  

 Features:

• Scale High Powered Headlights
• CX1 Lighting Controller
• Easy Plug and Play into stock RX
• High Quality Components 
• Higher Gauge wires over stock for long life
• Expandability

Includes:

• 1pc CX-1 Light Controller
• 1 pair Attack White Headlight
• 1pc Dual Red 3mm LED Taillights
• 1pc Dual Amber 3mm LED Front Running Lights
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers
• 3D Printed Rear Taillight Buckets

• CX-1 Controller
• Attack Headlights
• Tail Lights
• Plug & Play
• 3D Buckets

Axial SCX24 Ford Bronco

MyTrickRC's Axial SCX24 Ford Bronco Light Kit is the brightest on the market! You get the same Attack headlights used in our 1/10 scale kits!

Some great features of the Axial SCX24 Ford Bronco Light Kit are Attack Headlights that offer a ultra-scale look.

Additionally, the Axial SCX24 Ford Bronco Light Kit comes with our all new CX1- light controller powers 3 High-Power and 4 low Voltage for standard LEDs. The Axial SCX24 Ford Bronco Light Kit also includes Orange Front Bumper lights as well as Red Taillights. Keeping things just as accurate on a smaller scale.  

 Features:

• Scale High Powered Headlights
• CX1 Lighting Controller
• Easy Plug and Play into stock RX
• High Quality Components 
• Higher Gauge wires over stock for long life
• Expandability

Includes:

• 1pc CX-1 Light Controller
• 1 pair Attack White Headlight
• 1pc Dual Red 3mm LED Taillights
• 1pc Dual Amber 3mm LED Front Running Lights
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers
• 3D Printed Rear Taillight Buckets

• CX-1 Controller
• Attack Headlights
• Tail Lights
• Plug & Play
• 3D Buckets

Axial Honcho Light Kit HB-2

 The perfect complement to any Honcho is the ability to go at anytime day or night!

MyTrickRC's Axial SCX10.2 Honcho Light Kit Completes your Axial Honcho build. The SCX10.2 Honcho has a long list of killer features like Attack Headlights that are Crazy Bright. The Axial SCX10.2 Honcho Light Kit also is ready to add Rock Lights. For sure, our Axial SCX10.2 Honcho Light Kit takes it to the next level!

But in addition we include parts for roof Light Bars. This makes the Axial SCX10.2 Honcho Light Kit Easier than Ever to install and get Awesome Results! True to the MyTrickRC philosophy, the Axial SCX10.2 Honcho Light Kit is a direct fit to the 10.2 Honcho, and does require some cutting or gluing. Plus the Axial SCX10.2 Honcho Light Kit is super Expandable, so you can always add Light Bars and other Attack lights if you want. Now that's how to Trick Out your RC! The kit comes standard with our HB-2 Light Controller; a sleek, easy to setup, and simple to use Light Controller featuring 6 individual Output Ports (2 High Power, 1 Headlight, and 3 Standard Low Power). This Port configuration gives you the ability to create various combinations of 5 and 3mm LEDs, Rock Lights, etc. in various colors!

• 5" Light Bar, Attack High Power Headlights, Rear Tail Lights, Front Marker Lights
• Sleek looking LED Headlights and Curved Light Bars
• 5" Attack Light Bar mounts to Roof. Installation is super easy
• Expandable System = Adding More Lights is Plug-and-Play
• HB-2 Lighting Controller
• Ultra Bright LEDs, MyTrickRC does not compromise on component quality
• Impact Resistant Light Bar Design can take a beating

Axial 10.2 Honcho Light Kit Includes:

• 1pc 5" Attack Light Bar with Custom Mounts (attaches to roll cage using existing screws)
• 1pc Attack High Power Headlights
• 1pc 3mm Dual Yellow/Amber Marker Lights
• 1pc 3mm Dual Red Tail Lights
• 1pc HB-2 Lighting Controller
• Zip Ties and Zip Tie Mounts
• Attack Scale Bumper Stickers

• Ultra Bright System
• 5" Light Bar
• Attack Headlights
• Tail Lights
• HB-2 Controller

Axial 2017 Wrangler Light Kit HB-2

Trick out your Axial 2017 Wrangler with a MyTrickRC Light Kit!

• 5" Light Bar, High Power Headlights, Rear Tail Lights, Front Marker Lights
• Sleek looking LED Headlights and Curved Light Bars
• 5" Attack Light Bar mounts to Roof - Installation is super easy
• Ultra Bright LEDs, MyTrickRC does not compromise on component quality
• Impact Resistant Light Bar Design can take a beating
• 6 Output Ports (2 Hi-Power / 1 Headlight / 3 Standard)
• ON/OFF Switch so you can turn off the lights to save battery and prevent over-discharge
• Expandable System - Adding More Lights is Plug-and-Play! Easily add Rock Lights or Underglow

Axial 2017 Wrangler Kit Includes:

• 1pc 5" Attack High Power Light Bar with Mounts
• 1pc Attack High Power Headlights
• 1pc 5mm Dual Red Tail Lights
• 1pc 5mm Dual Yellow/Amber Front Marker Lights
• 1pc HB-2 Lighting Controller
• Zip Ties and Zip Tie Mounts
• MyTrickRC Stickers

• Ultra Bright System
• 5" Light Bar & Headlights
• Tail & Front Markers
• HB-2 Controller
• Easily Expandable

Element Gatekeeper Light Kit

Element Gatekeeper Light Kit is the perfect compliment to your Gatekeeper. You'll light up the trail like no other!  

The MyTrickRC Element Gatekeeper Light Kit is nice and compact, and offers some great features including a High Powered 2 Inch Light Bar upfront combined with four Attack Rock Lights, and some wicked Tail Light Pods. No Lighting controller needed on this one, its all powered off our Attack Light Power Regulator, drawing power directly from the receiver! It's Plug and Play and the Lights will be ON whenever the truck is On. 

If you ever want to upgrade this kit to power off a Dragon Controller instead of the Light Bar Regulator, you can easily do that.  All in this kit LEDs are compatible with our Dragon Controller.

Features:

• Hi Performance / Low Cost
• Easy Installation
• Minimal Wiring
• Plug and Play
• Tons of Light

Includes:

• 1- 2" Attack Light Bar
• 2- Pair High Power Spot Lights
• 1- Pair Red 9mm Wafer LEDs
• 1- MyTrickRC Light Bar Regulator
• 1- 4-Way LED Splitter
• 3D Printed S4 Pods
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

Installation notes

• All LEDs Zip Tie Into Place
• Hinge Function Not Affected By Wires
• No Modifications Needed
• Easy Installation

• Ultra Compact Design
• High Intensity LEDs
• Taillight Pods
• Includes Rock Lights
• Plug and Play

Element Knightrunner Light Kit

The perfect complement to your Knightrunner, is the ability to go at anytime; day or night!

The Element RC Knightrunner Light Kit is a Deluxe, Hight Power, Light Kit based on the HB-2 Controller and it really completes the Overlander look for this beautiful truck.  Plus the Element Knightrunner Light Kit pumps out TONs of Light, so any of your friends who don't have this kit will be envious of the Scale Look and amazing performance.  

The Element Knightrunner Light Kit is very easy to install, and add future Light Bars, Rock Lights, Wafers, or other accessory LEDs to.  Look for more Sweet accessory lighting from from MyTrickRC for this truck, we are working on them now! 

Features:

• ON/OFF Switch
• Easy Installation 
• Waterproof Controller and LEDs
• In-Line Quick Disconnects between Body and Chassis

Kit Includes:

• 1-HB-2 Controller
  
• 1-Attack Headlights
• 2-Attack Rock Lights
• 1-3mm Dual Amber 
• 1-3mm Dual White
• 1-5mm Dual Red 
• 1-4-Way LED Splitter
• 1- 27mm White Strip LED
• 1- L7 3D Printed PODs & Lenses

Installation Notes

• This light kit was designed to work with all the light bucket files offered by Knight Customs, so it's plug and play!
• Installing our attack headlights will work with the Knight customs LED mount

Attack 1" L7 Pods Bar Install Notes

• Align Light Bars then drill holes in Bumper for M2 screws. 
• Use a body reamer or pen vise to start a hole using the Light Bar as a guide
• Screw Light Bars in place

Install your M2.5 screw directly into the plastic bumper, creating threads Reinstall screw with Attack L7 in place

• HB-2 Controller
• Sleek L7 Pod
• Rock Lights
• Running Lights
• Expandable

Vanquish VS4-10 and Phoenix Light Kit 

Want a serious Light Kit for your VS4-10 or Phoenix? Look no further than MyTrickRC's Vanquish VS4-10 and Phoenix Light Kit. 

The Vanquish VS4-10 Phoenix Light Kit includes High Power Attack Headlights, Rock Lights, and Tail lights. Additionally, the Vanquish VS4-10 and Phoenix Light Kit is expandable, so if you want to add more Rock Lights, Running Lights, Interior Lights, or a Light Bar you easily can.  

This kit works equally well with the original VS4-10 and Phoenix Limited, and the Pro. 

Vanquish VS4-10 and Phoenix Light Kit features:

• Waterproof LEDs

• Easy Installation

• In-Line Quick Disconnects between Body and Chassis

Includes:

• HB-2 LED Light Controller 
• 1 Pair of Attack High Power Headlights
• 2 Pairs Attack Rock Light Pods
• 1 Pair 5mm Tail Lights
• 3D Printed Headlight Bezels
• Zip Ties and Zip Tie Mounts for clean wiring managment
• MyTrickRC Stickers

Vanquish VS4-10 and Phoenix Light Kit Highlights

• Simple Installation
• 3D Printed Headlight
• Rock Lights Included
• Tail Lights

Rock light Installation Photos

With the TRX4 Defender UF-7 Light Kit you can quickly and easily add a Scale Light System to your Traxxas Defender.   This sweet system has Dual LED Headlights, Front Markers, Turn Signals, Tail/Brake, and Reverse!   And with the custom designed 3D Printed Headlight and Tail Light Holders, and Plug and Play electronics, installation is a snap.  This is the absolute best system on the Market for those who want Scale Lighting on their Defender, and that you can count on to work as claimed.  With thousands of these systems in the market, you can buy with confidence knowing you will be in the company of many others who love MyTrickRC Lighting Systems.

Some of the great features you will get with the TRX4 Defender UF-7 Light Kit are

• Scale Lighting System including Headlights, Tail/Brake Lights, Reverse Lights, and Turn Signals (Turn Signals can easily be Configured as Running Lights if Preferred)
• Scale Light Buckets match the Stock Light Clusters, and use Existing Stock Hardware for Mounting
• Sleek looking Dual LED Headlights
• Rock Solid UF-7 Lighting Controller is a is an Industry Leader for Scale Lighting
• Ultra Bright LEDs, MyTrickRC does not compromise on component quality
• Defender Kit uses standard 3mm LEDs that are are water tolerant, and easily serviceable
• Impact Resistant Plastic Design and Construction  

TRX4 Defender UF-7 Light Kit Includes:

• 1 Set 3D Printed Headlight Buckets with LED Retaining Brackets
• 1 Set 3D Printed Tail Light Buckets with LED Retaining Brackets
• UF-7 Multi Function Lighting Controller
• 4pcs  3mm Dual White LEDs (8LEDs for Headlights, and Reverse Lights)
• 1pc 3mm Dual Red LEDs (2LEDs for Tail/Brake Lights)
• 1pc 3mm Single Orange LEDs (4LEDs for Turn Signals/Running Lights)
• Zip Ties and Zip Tie Mounts for clean wiring managment
• Attack Scale Bumper Stickers

NOTES

• 6" Light Bar Sold Separately

• 3D Printed Headlight
• Tail Light Buckets
• Scale Brake and Reverse
• Optional Turn Signals
• UF-7 Lighting Controller

Trick Out your Traxxas TRX4 Defender with a MyTrickRC Light Kit!

Our TRX4 Defender Light Kit HB-2 starts with a 5" Light Bar complemented by Attack High Power Headlights for Insane Brightness! To this add Front Running Lights and Tail Lights and you've got an awesome Scale vehicle!

This easy to install Kit features the HB-2 Lighting Controller. The TRX4 Defender HB-2 Kit with 5" Light Bar is fully Plug and Play so Installation is Easy and Fun.

It's also Super Easy to add Rock Lights (SKU:  MYK-TDR) to the TRX4 Defender HB-2 Kit with 5" Light Bar. Add Four or Eight Rock Lights, and it takes this truck to the Next Level of Insane Light Output. This is a Huge Benefit on the trail when you need lots of light for safe hiking. You can Really Light Up the Trail with some Rock Lights. MyTrickRC Rock Lights are Plug and Play with the TRX4 Defender HB-2 Kit with 5" Light Bar.

TRX4 Defender Light Kit HB-2 Features:

• Scale Lighting System including 5" Light Bar, High Power Headlights, Rear Tail Lights, Front Running Lights 
• Custom Headlight Reflectors provide a Scale look, and this system uses existing stock screws for simple mounting 
• Sleek looking LED Headlights and Curved Light Bars 
• 5" Attack Light Bar mounts to stock roll cage. Installation is super easy and does not require any cutting or mods to stock parts
• Lighting Harness with Circuit Board Light Clusters has minimal wiring so installation is quick and easy
• Expandable System - Adding High Power Light Bars, Spot Lights, or Rock Lights is Plug-and-Play
• HB-2 Lighting Controller is Quality Scale Lighting
• Ultra Bright LEDs, MyTrickRC does not compromise on component quality
• Impact Resistant Light Bar Design can take a beating

TRX4 Defender Light Kit HB-2 Includes:

LIGHT BAR

• 1pc 5" Attack Light Bar with Mounts

BODY LIGHT SYSTEM

• 1pc Lighting Harness with
• 1 Pair of Headlight Clusters including High Power Headlights, White and Orange Running Lights
• 1 Pair of Tail Light Clusters including Tail Lights
• 1set Custom Headlight Reflectors and Retaining Brackets
• 1pc HB-2 Light Controller
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

NOTE - for Traxxas Battery users

A Traxxas Battery Adapter (sku MYK-RTX) is required with this kit if you plan to use a Traxxas Battery on your vehicle.

Traxxas Battery Adapter

OPTIONAL - Rock Light available are for this vehicle:

4-LED Rock Light Set

8-LED Rock Light Set

• Ultra Bright
• 5" Light Bar
• Scale Headlights
• Scale Tail Lights
• HB-2 Controller

Traxxas K5 Blazer Light Kit HB-2

With the Traxxas K5 Blazer Light Kit you can quickly and easily setup your K5 Blazer with a trail ready Light System. The Traxxas K5 Blazer Light Kit includes Attack Headlights, Front and Side Marker Lights, Tail Lights, and custom Headlight Bezels. Also, since the Traxxas K5 Blazer Light Kit is based on the HB-2 Controller, it's easy to add Rock Lights, Light Bars, or any of MyTrickRC's Attack Headlights.

Traxxas K5 Blazer Light Kit Features:

• Scale Lighting System including Attack Headlights, Tail Lights, Front and Side Marker Lights
• Custom Headlight Bezels
• Easy Installation - Requires Minimal Tools

Traxxas K5 Blazer Light Kit Includes:

• 1 Pair of Attack High Power Headlights
• 2pcs 3mm Dual Orange LEDs for Front & Side Marker Lights
• 1pc 5mm Dual Red Tail Lights
• Custom Headlight Bezels
• HB-2 Lighting Controller
• Zip Ties and Zip Tie Mounts for clean wiring management
• Attack Scale Bumper Stickers

NOTE - for Traxxas Battery users

A Traxxas Battery Adapter (sku MYK-RTX) is required with this kit if you plan to use a Traxxas Battery on your vehicle.

Traxxas Battery Adapter

OPTIONAL - Rock Light available are for this vehicle:

4-LED Rock Light Set

8-LED Rock Light Set

• Attack Headlights
• Marker Lights
• Tail Lights
• Headlight Bezels
• HB-2 Controller

Take your TRX4 Bronco to the next level with MyTrickRC's TRX4 Bronco Light Kit!  This kit includes the well known Attack High Power Headlights,  Front and Side Marker Lights, and Tail Lights. The kit is fully expandable, with the ability to add Rock Lights, Light Bars, and Spot Lights.  

The TRX4 Bronco Light Kit has some great features including Easily Expandable add Rock Lights, Light Bars, and Spot Lights, Waterproof LEDs, Scale Lights, and more! This is great for power management. simple Plug and Play Installation, and it was built specifically to fit your truck.  Also, we offer a detailed instruction video to make installation easy. The kit comes standard with our DG-1 Light Controller; a sleek, easy to setup, and simple to use light controller featuring 6 individual output ports 4 standard power and 2 High power. This port configuration gives you the ability to create various combinations of 3 and 5mm LEDs, Rock Lights, etc. in various colors! 

Minor modifications to the body are required for installation.

This kit also works with the High Trail TRX4 Bronco!

                Back in Stock!

TRX4 Bronco Light Kit Includes:

• DG-1 Controller
• 1pcs Attack High Power Headlights
• 1pcs 5mm Dual Red Tail Lights
• 1pcs 3mm Dual Front Turn Signal Marker Lights
• 1pc 3mm Quad Front and Rear Side Marker Lights
• 1pc 3D printed LED mounts

NOTE - for Traxxas Battery users

A Traxxas Battery Adapter (sku MYK-RTX) is required with this kit if you plan to use a Traxxas Battery on your vehicle.

Traxxas Battery Adapter

OPTIONAL - Rock Light available are for this vehicle:

4-LED Rock Light Set

8-LED Rock Light Set

• High Power Headlights
• Side Marker Lights
• Tail Lights
• Reverse Lights
• DG-1 Controller

Traxxas TRX4 Bronco Light Kit HB-2

Trick Out your Traxxas TRX4 Bronco with a MyTrickRC Light Kit! This Kit includes our well known Attack High Power Headlights as well as Tail Lights and plenty of Marker Lights. The result is an authentic Scale looking vehicle.

At the heart of this Kit is our HB-2 Lighting Controller which features 6 individual Output Ports (2 High Power, 1 Headlight, and 3 Standard Low Power). These give you plenty of freedom to Expand - easily add one of our super bright Light Bars or Rock Lights or Spot Lights!

Installation is simple Plug and Play - no soldering required. Note that minor modifications to the Body are required for installation.

TRX4 Bronco Light Kit Includes:

• 1 Pair of Attack High Power Headlights
• 1pc 5mm Dual Red Tail Lights
• 1pc 3mm Dual Orange Front Marker Lights
• 1pc 3mm Quad Red/Orange Rear/Front Side Marker Lights
• 1set LED Mounts
• HB-2 Lighting Controller

NOTE - for Traxxas Battery users

A Traxxas Battery Adapter (sku MYK-RTX) is required with this kit if you plan to use a Traxxas Battery on your vehicle.

Traxxas Battery Adapter

OPTIONAL - Rock Light available are for this vehicle:

4-LED Rock Light Set

8-LED Rock Light Set

• High Power Headlights
• Tail Lights
• Front Marker Lights
• Side Marker Lights
• HB-2 Controller

Traxxas TRX4 Sport Light Kit HB-2

With the Traxxas TRX4 Sport Light Kit you can quickly and easily setup your TRX4 Sport with a trail ready Light System. The Traxxas TRX4 Sport Light Kit includes Custom Tail Light Bezels for the RTR Version, Front Marker Lights, Tail Lights, and Rock Lights!

Also, since the Traxxas TRX4 Sport Light Kit is based on our HB-2 Light Controller, it's easy to add Light Bars or any of MyTrickRC's new Wafer Headlights. Another great thing about the Traxxas TRX4 Sport Light Kit as it can be used on either the RTR or Kit version of the Truck.

Traxxas TRX4 Sport Light Kit Features:

• Scale Lighting System including Attack Headlights, Rock Lights, Tail & Running Lights
• Custom Tail Light Bezels for RTR Body
• HB-2 Light Controller
• Easy Installation - Requires Minimal Tools

Includes:

• 4 Pairs of Attack High Power Headlights & Rock Lights (kit uses Headlights as Rock Lights)
• 1pc 3mm Dual Yellow/Amber Front Marker Lights
• 1pc 5mm Dual Red Tail Lights
• Custom Tail Light Bezels for RTR
• 1pc HB-2 Lighting Controller
• Zip Ties and Zip Tie Mounts for clean wiring management
• MyTrickRC Stickers

NOTE - for Traxxas Battery users

A Traxxas Battery Adapter (sku MYK-RTX) is required with this kit if you plan to use a Traxxas Battery on your vehicle.

Traxxas Battery Adapter

• Attack Headlights
• Rock Lights
• Front Marker Lights
• Tail Light Buckets
• HB-2 Controller

The Proline Metric Light Kit is the perfect compliment to your Proline Metric Build. The

MyTrickRC Proline Metric Light Kit offers some great features including Paint Mask Stickers for Headlights and Tail Lights. Also, MyTrickRC offers Free Official Knight Customs 3D print yourself STL files, so you can save some money and 3D print your own Buckets. If you don’t have a 3D printer, we offer them on our Website:

Or, you can find them on the Knight Customs Shapeway Store. Either way you go, the Proline Metric Light Kit offers great scale features including Headlights, Tail/Brake, Reverse, and Running Lights that can act as Turn Signals, or just Marker Lights.

Since the Proline Metric Light Kit is based on the UF-7C controller you have some other great Upgrade Options available to you. Want to add a scale functioning Center Brake Light, Light Bar, or Rock Lights? These upgrades are easy with the UF-7C, you can add any single Attack Light Bar, or up to 3 pairs of Spot Lights to the UF-7Cs Pig Tail Output*

* UF-7C Light Bar Power Adapter is recommended if you want to add Attack Lights to your system. This offers a Plug and Play solution that also regulates the correct power to your Attack Light Bars.

**Alternate Light Bars such as a Proline Light Bar can also be powered off the UF-7C’s Pigtail. However, a special adapter cable is required (JST to Futaba)

• DIY 3D Printed Buckets
• UF-7C Deluxe Controller
• Easily Expandable
• Headlights + Tail Brake
• Running/Turn + Reverse

The Redcat Gen 8 and AXE Int Scout Kit

RedCat Gen and AXE 8 Fans, MyTrickRC is excited to present our new RedCat Gen 8 Int Scout Kit to you! 

RedCat has made a splash with the Gen 8 and AXE Scout, and we are here to take it even further. The scale molded grill and tail lights make this truck look great right out of the box, but with the MyTrickRC Light System it's taken to a new level!  Our Rock Solid UF-7C is the perfect fit for this truck.  It's Scale lighting features include Dual Headlights, Dual Front Running Lights, Tail/Brake, Rear Running Lights, and Reverse.  Additionally, it features automatic Hazard Lights.  They automatically turn on after 15 sec at rest.  And if you don't want Hazard Lights, you can simply turn them Off!  The UF-7C also offers Remote ON/OFF Control, but this feature requires a 3rd channel, not included on the stock truck.  If you upgrade your radio system to one with a 3rd channel, and purchase a second Y Cable for the UF-7C then you automatically get ON/OFF Control.   

Oh, did we mention this Plug and Play Kit includes a special Splitter Cable that lets you easily add the lights to the bumpers, while leaving the controller mounted to the bodies.  There is an in-line disconnect so you can easily separate your body from LEDs on the chassis. 

MyTrickRC's RedCat Gen 8 and AXE Int Scout Kit really is the Ultimate Scale Light Kit for this truck. And at my TrickRC we are all about helping you get Great Results with Minimal Effort.

Features: 

• Complete Light Kit with UF-7C Controller
• Four Headlights
• Running Lights in Bumpers
• Automatic Hazard Lights
• Tail/Brake and Reverse
• Plug and Play, Powers off Receiver
• High Quality Construction and Materials
• Remote ON/OFF Control on 3rd Channel (this included feature requires you to upgrade your vehicles radio system to one with a 3rd channel, and add a second Y-Cable)

Includes:

• 1pc UF-7C Lighting Controller
• 3pcs 5mm Dual White Headlights and Reverse
• 3pcs 5mm Dual Red Tail/Brake and Running
• 2pcs 5mm Dual Orange Front Running 
• 4-Way LED Y-Cable with Quick Disconnect
• Zip Ties and Zip Tie Mounts for clean wiring management

• UF-7C Controller
• Plug & Play
• Working Tail & Reverse
• Auto Hazard Lights
• Expandable

UF-7 Short Course Truck Light Kit 

The UF-7 Short Course Truck Light Kit was one of the first Lighting Kits MyTrickRC ever made. 

This Rock Solid System has stood the test of time.  Many customers tell us this system has outlived their vehicles, only to end up lighting their next vehicles.  That shows the value your get with MyTrickRC and the UF-7 Short Course Truck Light Kit. 

Quality, Flexibility, and Simplicity are the building blocks the UF-7 System is built on.  This system can be easily added onto,  or changed up.  Just connect the desired LEDs and select the desired MODE, plug and play!

The UF-7 has 10+ MODE options.  Some MODEs are for TRUCKS, other for CARS, AIRPLANES, BOATS, PROP Lighting, and EMERGENCY VEHICLES.  The blink patterns of these MODEs create Scale Realism 

Includes:

• 2pcs 5mm Dual WHITE Headlights
• 2pcs 3mm Dual WHITE Driving Lights
• 1pcs 3mm Dual RED Tail-Brake Lights
• UF-7 Universal Light Controller
• Power Cables to power off your car’s battery, or 9V battery
• Mounting Hardware

• Built for Bashers
• UF-7 Controller
• 5mm Headlights
• 3mm Driving Lights
• Functioning Tail/Brake

The UF-7R Off Road Rock Crawler Light Kit is MyTrickRC's first Rock Crawler Kit, and is still a very popular Kit!  The Rock Solid and Well Proven UF-7R Controller is at the heart of the system.   The UF-7R offers functioning Brake Lights, optional Reverse Lights, Full Brightness Headlights, Driving Lights, and Running Lights.

The UF-7R Off Road Rock Crawler Light Kit is also easy to change-up.  Simply switch out the LEDs and select the desired MODE - truly Plug and Play!   No other system offers the value of MyTrickRC Lighting Systems, as these are built to last,  and perform as claimed.  The UF-7R  was designed with Quality, Durability, and Simplicity in mind.

UF-7R Off Road Rock Crawler Light Kit Includes:

• 1pcs 5mm Dual WHITE Headlights
• 3pcs 3mm Dual WHITE Driving Lights
• 1pcs 3mm Dual ORANGE Front Marker Lights
• 1pcs 3mm Dual RED Tail-Brake Lights
• UF-7R Universal Light Controller
• Power Cables to power off your car’s battery or 9V battery
• Mounting Hardware

*RPM Light Bar Canisters not included.

• UF-7R Controller
• Headlights
• Driving Lights
• Dual Orange
• Tail/Brake

Element RC Utron Light Kit

Trick out your Element RC Utron with a MyTrickRC Light Kit! The Element RC Utron Light Kit has everything you need for Lighting Your Way - Rock Lights, Headlights, Tail Lights, and Marker Lights.

The Element RC Utron Light Kit features our CX-1 Lighting Controller at its heart. CX-1 is a Compact LED Light Controller that powers off of a free port in your Receiver or one the 5.0V ports Element RC provides on their Reedy ESC. The Element RC Utron Light Kit also includes Custom Tail Light Buckets for securely fitting your Tail Lights to the stock body. The Element RC Utron Light Kit is Plug and Play and easy to install.

Features:

• Waterproof LEDs
• Easy Plug and Play Installation

Kit Includes:

• 2 Pair Attack Spot Light LEDs as Rock Lights
• 1 Dual White 5mm LED Headlights
• 1 Dual Red 3mm LED Tail Lights
• 1 Dual Orange 3mm LED Marker Lights
• CX-1 Lighting Controller
• Zip Ties and Zip Tie Mounts for clean wiring management
• MyTrickRC Decal

• Rock Lights
• Headlights
• Tail Lights
• Marker Lights
• CX-1 Controller